MECHANICAL PROPERTIES OF AN ALUMINIUM OR SILICON CARBIDE COMPOSITE CONNECTING
ABSTRACT
Metal Matrix Composites (MMC’s) have evoked a keen interest in recent times
for potential applications. Composite materials like Particle-reinforced Aluminium Silicon carbide (Al/SiC) Metal-Matrix
Composite is gradually becoming very important materials in manufacturing industries e.g. aerospace, automotive
and automobile industries due to their superior properties such as light weight, low density, high strength to weight
ratio, high hardness, high temperature and thermal shock resistance, superior wear and corrosive resistance, high
specific modulus, high fatigue strength etc. In this study, Connecting rods made from commercial pure aluminum
alloy (about 99.1% purity) / Silicon carbide (SiC) reinforced particles metal-matrix composites (MMCs) are
fabricated by green sand casting. The MMCs connecting rods (Big end ø 68 mm, pin end ø 32 mm, 136 mm
Center to Center height) are prepared by varying the reinforced particles by weight fraction ranging from 0%, 5%,
10%, 15% and 20 %. The average reinforced particles size of SiC are 75 microns (µm), 125 microns (µm) and
300 microns (µm) respectively. The micro-structure and mechanical properties like Ultimate tensile strength (MPa),
Breaking strength (MPa), Elastic Modulus (Mpa), % Elongation, Hardness (HRB), are investigated on prepared
specimens of MMCs. It was observed that the hardness of the composite is increased with increasing of reinforced particle weight fraction. The tensile strength is increased with rising of reinforced weight fraction.
Different mechanical tests were conducted and presented by varying the particle size and weight fractions of the Silicon carbide (SiC) particulates.
INTRODUCTION
A composite is considered to be any multiphase material that exhibits a significant proportion of the properties of
both constituent phases such that a better combination of properties is realized. This is termed as the ‘principle of
combined action’ (2). According to this principle, better combinations are fashioned by the judicious combination
of two or more distinct materials. All composites generally have one thing in common: a matrix or binder combined
with a reinforcing material, within which is a dispersion of one or more phases of another material.
Metal matrix composites, as we know today have evolved significantly during the past few years. The primary
support of the composites has come from the aerospace industry for airframe and spacecraft structures. More
recently the automotive, electronics and recreation industries have been working diligently with these composites.
The driving force behind the development of most of the existing composites has been their capability to be
designed to provide needed types of material behaviour.
The focus of research and development in the metal matrix composites (MMCs) area has recently shifted toward
low-cost discontinuously reinforced composites which are targeted for automotive and aerospace applications.
The optimum properties of MMCs and the enhanced performance from these materials however depend on the
judicious selection of the metallic matrix material, reinforcing phase and the processing technique. The composite
fabrication technique is an important consideration. For a given set of constituents, the fundamental link between
properties and cost is determined by the fabrication method. Processing in general, is concerned with the
introduction of reinforcement into the matrix with a uniform distribution. The major hurdle is the achievement of
proper bonding between the matrix and the reinforcement in order to attain good load transfer between phases.
A wide variety of fabrication techniques have been explored for metal matrix composites. These include liquid
phase methods, deposition of matrix from a semi solid or vapour phase, and solid state consolidation. Liquid
phase processing has attractive economic aspects. Chopped fibres, porous ceramics compacts and particulates
have been incorporated into matrix alloys. In some cases, pressure assistance has been used to infiltrate the
reinforcement with the molten matrix. These methods result in micro-structures dictated by the solidification of the
molten metal. The green sand casting technique has been among the simplest and the most economical
processes of fabricating the particulate metal matrix composites. However due to poor wetting of the ceramic
particles by molten alloy, the introduction and uniform dispersion of the reinforcement into the liquid matrix is difficult.
MECHANICAL PROPERTIES OF AN ALUMINIUM OR SILICON CARBIDE COMPOSITE CONNECTING